- Open Access
Comparison of enzymatic reactivity of corn stover solids prepared by dilute acid, AFEX™, and ionic liquid pretreatments
Biotechnology for Biofuels volume 7, Article number: 71 (2014)
Pretreatment is essential to realize high product yields from biological conversion of naturally recalcitrant cellulosic biomass, with thermochemical pretreatments often favored for cost and performance. In this study, enzymatic digestion of solids from dilute sulfuric acid (DA), ammonia fiber expansion (AFEX™), and ionic liquid (IL) thermochemical pretreatments of corn stover were followed over time for the same range of total enzyme protein loadings to provide comparative data on glucose and xylose yields of monomers and oligomers from the pretreated solids. The composition of pretreated solids and enzyme adsorption on each substrate were also measured to determine. The extent glucose release could be related to these features.
Corn stover solids from pretreatment by DA, AFEX, and IL were enzymatically digested over a range of low to moderate loadings of commercial cellulase, xylanase, and pectinase enzyme mixtures, the proportions of which had been previously optimized for each pretreatment. Avicel® cellulose, regenerated amorphous cellulose (RAC), and beechwood xylan were also subjected to enzymatic hydrolysis as controls. Yields of glucose and xylose and their oligomers were followed for times up to 120 hours, and enzyme adsorption was measured. IL pretreated corn stover displayed the highest initial glucose yields at all enzyme loadings and the highest final yield for a low enzyme loading of 3 mg protein/g glucan in the raw material. However, increasing the enzyme loading to 12 mg/g glucan or more resulted in DA pretreated corn stover attaining the highest longer-term glucose yields. Hydrolyzate from AFEX pretreated corn stover had the highest proportion of xylooligomers, while IL produced the most glucooligomers. However, the amounts of both oligomers dropped with increasing enzyme loadings and hydrolysis times. IL pretreated corn stover had the highest enzyme adsorption capacity.
Initial hydrolysis yields were highest for substrates with greater lignin removal, a greater degree of change in cellulose crystallinity, and high enzyme accessibility. Final glucose yields could not be clearly related to concentrations of xylooligomers released from xylan during hydrolysis. Overall, none of these factors could completely account for differences in enzymatic digestion performance of solids produced by AFEX, DA, and IL pretreatments.
Lignocellulosic biomass, including agricultural and forestry residues and herbaceous and woody crops , provides the only sustainable resource with potential for large-scale and low-cost production of liquid fuels and organic chemicals that are currently produced from dwindling and nonrenewable fossil resources that are major contributors to greenhouse gas emissions [1, 2]. Enzymatic hydrolysis is a key step in the biological conversion of lignocellulosic biomass into fuels and chemicals, with the high product yields important to commercial success [1–5]. Endoglucanases, exoglucanases, and β-glucosidase as well as supplementary enzymes such as xylanases and β-xylosidase are generally required to complete enzymatic hydrolysis effectively and efficiently [6–10]. However, to realize the high yields vital to commercial success of enzymatic conversion , most cellulosic biomass must be pretreated prior to enzymatic hydrolysis, and the choice of pretreatment not only affects enzymatic digestion performance but impacts upstream and downstream processing as well [1, 12]. To overcome the natural recalcitrance of cellulosic biomass, several biological, chemical, thermochemical, and physical pretreatment methods have been applied, but thermochemical pretreatments are often preferred due to a more favorable combination of capital costs, operating costs, and performance .
Among thermochemical pretreatments, hemicellulose or lignin removal and/or alternation by dilute acids, with just hot water, or base promise reasonable costs [11, 13, 14]. In particular, dilute sulfuric acid (DA) and ammonia fiber expansion (AFEX™) pretreatments are currently among the most promising from a combined cost and performance perspective . DA and hydrothermal pretreatments effectively remove and recover as sugars a large portion of hemicellulose as well as disrupting and dislocating lignin, while increasing cellulose digestibility [15–17]. The AFEX process pretreats biomass with anhydrous liquid ammonia at high pressure and moderate to high temperatures. Following pretreatment for a given time, the pressure is rapidly released resulting in biomass structure disruption and partial cellulose decrystallization that presumably enhance cellulose digestibility [18–20]. Lately, certain ionic liquids (ILs) such as the IL 1-ethyl-3-methylimidazolium acetate have been employed for pretreatment followed by addition of an anti-solvent to precipitate biomass . Such ILs remove most of the lignin from biomass and disrupt the native cellulose crystalline structure and hydrogen networks to form cellulose II, thus reducing biomass recalcitrance [22–24].
Various biomass physicochemical changes resulting from the action of different leading pretreatments have been reported to enhance cellulose enzymatic digestibility, such as surface area, pore volume, hemicellulose removal, lignin removal and/or dislocation, crystallinity reduction, and reduced cellulose degree of polymerization (DP) [25–31]. Of these many possible factors, hemicellulose removal and lignin dislocation are mainly credited with enhancing digestion by DA pretreatment [16, 17]. Creation of pore structures in biomass and disruption of lignin-carbohydrate complex (LCC) linkages enhance digestion for AFEX pretreatment [32, 33]. Increased surface roughness, reduced cellulose crystallinity, and expansion or even a transformation of the cellulose lattice have been reported to account for the beneficial effects of IL pretreatments on biomass [22, 34].
With several pretreatments being effective in achieving high sugar yields, it is vital to develop comparative data on sugar release from enzymatic hydrolysis of solids produced by each to facilitate identification of promising technologies. It is also important to measure key features influenced by each pretreatment to determine if enzymatic digestion can be related to any common characteristics, especially at the low enzyme loadings needed to be commercially viable . In line with these objectives, researchers from the University of California, Riverside (UCR; Riverside, CA, USA), supported by the BioEnergy Science Center (BESC; Oak Ridge, TN, USA), Michigan State University (East Lansing, MI, USA) supported by the Great Lakes Bioenergy Research Center (GLBRC; Michigan State University), and the Joint BioEnergy Institute (JBEI; Emeryville, CA, USA) collaborated to better understand how biomass pretreatments by AFEX, DA, and IL with much different deconstruction patterns impact glucose and xylose release from enzymatic digestion over a wide range of enzyme loadings. To provide comparative information, a single source of corn stover was used as the feedstock for all three pretreatments, and one source of commercial cellulases and accessory enzymes was applied to the pretreated solids. In addition to sugar release data, changes in composition of solids and enzyme adsorption capacity of pretreated biomass solids were also measured to determine if they could help explain performance differences. Other papers by this team are in progress to examine changes in other features of pretreated biomass and more fully follow key features that could account for the performance differences reported here.
Results and discussion
Compositional analysis of DA, AFEX, and IL pretreated corn stover
Table 1 summarizes the pretreatment conditions applied, compositions of raw and pretreated corn stover solids, and the amount of xylan and lignin removed by each pretreatment. It can be seen that DA removed about 87% of the xylan, resulting in solids with a very low xylan content of 6.5% and increased glucan content of 59.1%. AFEX pretreatment of corn stover, as a dry to dry process, did not solubilize much of the biomass during pretreatment, resulting in a negligible compositional change. However, IL pretreatment removed >90% of the lignin and >20% of the xylan originally in corn stover, resulting in solids with a lignin content of only 2.7% and glucan and xylan contents of 46.9% and 29.8%, respectively. These changes in composition are consistent with results from previously reported studies [31, 36, 37].
Enzymatic hydrolysis of pretreated corn stover solids and model compounds
Glucose yields from enzymatic digestion of pretreated solids
Enzymatic digestion was performed at solids loading of 1% (w/w) glucan to allow focus on how pretreatments impacted substrate digestion and avoid confusion by end-product inhibition of the enzymes; this approach is consistent with the National Renewable Energy Laboratory (NREL) Laboratory Analytical Procedure (LAP) . Enzyme loadings of 3, 6, 12, and 30 mg of total protein/g glucan in the raw biomass were applied at ratios of cellulase (Cellic® CTec2, Novozymes North America, Inc, Franklinton, NC, USA), hemicellulase (Cellic® HTec2, Novozymes North America, Inc), and pectinase (Multifect® Pectinase, DuPont™ Genencor® Science, DuPont Industrial Biosciences, Palo Alto, CA, USA), as shown in Table 2, that GLBRC had previously shown to give the highest sugar release from pretreated solids using their high-throughput microplate-based hydrolysis method . Although different enzyme mixtures were required to achieve the highest sugar yields in enzymatic hydrolysis of solids from each pretreatment, the total mass loadings of the enzyme combinations applied were kept the same. In addition, optimal ratios of enzyme components in the mixtures were not simply related to the composition of the pretreated solids. For example, DA pretreated corn stover had negligible amounts of xylan, but substitution of hemicellulases for some of the cellulase still improved yields, possibly due to synergies or other effects among the enzymes .
All enzymatic hydrolysis reactions were conducted at 50°C for time periods up to 120 hours. Sugar release is reported in terms of the glucose and xylose yield calculations described in the Materials and methods section, in which the amount of either sugar actually released is divided by the maximum amount of the respective sugar that could be released from a particular pretreated solid including the appropriate factors to account for mass changes in hydrolysis. The glucose yield calculation includes monomeric glucose plus cellobiose, while the xylose yield only takes into account the monomeric xylose released.
As shown in Figure 1, glucose yields from hydrolysis of DA and AFEX pretreated corn stover were rapid in the first 8 hours and then slowed down considerably to almost level off after 72 hours at both 3 and 30 mg protein/g glucan loadings. As expected, glucose yields were always higher at the higher enzyme loading, particularly for AFEX and DA pretreated solids. Corn stover solids from IL pretreatment had greater initial glucose yields compared to either DA or AFEX pretreated corn stover and nearly reached its maximum glucose yield in only 8 hours. Adding more enzyme increased glucose yields from IL pretreated solids less than from the other two pretreatments because the yields were already high for IL solids.
Figures 2 and 3 compare the 1-hour and 72-hour glucose yields from enzymatic hydrolysis at four enzyme loadings applied to solids produced from corn stover by the three pretreatments. Figure 2 shows that the 1-hour glucose yields of all substrates increased almost linearly with enzyme loading. Furthermore, IL pretreated corn stover solids displayed the highest 1-hour hydrolysis yield at all enzyme loadings followed by DA and then AFEX. Increasing the enzyme loading from 3 to 30 mg protein/g glucan increased glucose yields from IL pretreated solids by 40% in the first hour of hydrolysis. The 1-hour glucose yields from DA corn stover at the highest enzyme loading of 30 mg/g glucan were about six times higher than at the lowest enzyme loading of 3 mg/g glucan. The 1-hour glucose yield from solids from AFEX pretreatment was slightly lower compared to DA at the lowest enzyme loading but 10% lower at the high enzyme loading. Thus, the 1-hour glucose yield from AFEX pretreated corn stover did not benefit from higher enzyme loadings as much as solids from the other two pretreatments.
The 72-hour glucose yields from enzymatic hydrolysis of the pretreated solids were also compared for the three pretreatments at four enzyme loadings, as shown in Figure 3. Overall, higher enzyme loadings resulted in higher glucose yields, as expected, but the benefit of adding more enzymes varied with pretreatment. For example, as shown in Figure 3, when the enzyme loading was increased from 3 to 30 mg/g glucan in raw biomass, the 72-hour glucose yields for DA and AFEX corn stover increased by about 30% and 30.5%, respectively, while solids from IL pretreatment of corn stover had only about a 10% enhancement in glucose yield as it was already close to the maximum at the low enzyme loading. As seen in Figure 3, at 30 mg total protein for the optimized enzyme mixtures/g glucan in raw corn stover, 72-hour glucose yields from enzymatic hydrolysis were 93.8% for DA pretreated corn stover, 91.6% for IL, and 82.1% for AFEX. Avicel® and regenerated amorphous cellulose (RAC) model compounds realized about 42% and 16% increases in glucose yields, respectively, over the range of enzyme loadings applied.
Xylose monomer and oligomer yields
The liquid samples from 4, 24, and 72 hours of enzymatic hydrolysis of solids produced by DA, AFEX, and IL pretreatments of corn stover were analyzed for longer chain length glucooligomers (> cellobiose) and xylooligomers by post-hydrolysis of liquid samples from pretreatment with 4% w/w DA at 121°C for 1 hour . Figure 4 reports both xylose monomer and xylooligomer yields following 72 hours of enzymatic hydrolysis of solids produced by DA, AFEX, and IL pretreatments of corn stover at total enzyme protein loadings of 3 and 30 mg/g glucan in raw biomass for the same optimized enzyme mixtures as used to obtain glucose yields. Results from enzymatic hydrolysis of the model compound beechwood xylan are also included over a range of 3 to 30 mg of just HTec2 xylanase protein/g xylan. Figure 4 shows that about a quarter of the total xylose in solution was released as xylooligomers during hydrolysis for all pretreated solids and remained at about the same fraction of the total for both enzyme loadings for these three solids. However, a much higher fraction of the total xylose in solution was as oligomers for beechwood xylan, particularly at the lower enzyme loading, most likely due to low β-xylosidase and other accessory activities . When comparing solubilized xylan yields from enzymatic hydrolysis of pretreated solids at the 10 g glucan/L employed for evaluating substrate breakdown by enzymes, it should be kept in mind that compositional variations in the substrates from each pretreatment led to quite different ratios of enzyme protein to xylan content. As shown in Figure 4, at an enzyme loading of 30 mg total protein/g glucan in raw corn stover, the total xylose monomer plus oligomer yields for solids produced from corn stover by DA, AFEX, and IL were 83%, 68%, and 77%, respectively, with oligomers contributing about 9%, 14%, and 12%, respectively, to these amounts.
Percentage of oligomers released during hydrolysis
As shown in Figure 5A for glucooligomers and Figure 5B for xylooligomers, longer hydrolysis times and increased enzyme loadings both reduced the proportion of gluco- and xylooligomers. At the early stage of hydrolysis or for lower enzyme loadings, the maximum glucooligomer percentage was less than 13% for AFEX followed by 12% for IL and 6% for DA. Figure 5A suggests that application of mixtures of CTec2, HTec2, and Multifect Pectinase enzymes optimized individually for each pretreatment achieved essentially complete digestion of the glucan to monomers for all three pretreated materials at high enzyme loadings.
Figure 5B shows that hydrolysis of xylooligomers was less complete than for glucooligomers. For hydrolysis of AFEX and IL pretreated corn stover solids, approximately 20% or more of the total xylose in solution persisted as oligomers even after hydrolysis for 72 hours at an enzyme loading of 30 mg/g glucan in the raw material. Hydrolyzate from enzymatic hydrolysis of AFEX pretreated solids contained the highest amount of xylooligomers followed by IL and DA. Overall, enzymatic hydrolysis of DA pretreated corn stover released the lowest percentage of both glucooligomers and xylooligomers.
Effect of xylan and lignin removal on enzymatic digestion
Figure 6 plots 1-hour and 72-hour glucose yields from enzymatic hydrolysis against lignin and xylan removal. Xylan removal has been reported to enhance glucan digestibility by improving cellulose accessibility  and/or reducing cellulase inhibition by xylooligomers produced from partial hydrolysis of xylan [43–45]. However, these results show that the 1-hour glucose yields did not follow a clear trend with xylan removal, and 72-hour yields only correlated with xylan removal at the two highest enzyme loadings.
From Figure 6, it is apparent that the 1-hour glucose yields correlated well with lignin removal at all enzyme loadings, while such a relationship was only apparent for 72-hour results at the lowest enzyme loading. This result is consistent with reports that lignin is one of the key biomass components impacting enzymatic digestion of cellulosic biomass [2, 34]. Lignin is believed to not only hinder cellulose accessibility as a result of LCC linkages but also impact cellulase effectiveness by unproductive binding of enzymes [31, 46, 47].
It has been shown that xylobiose and xylooligomers with higher DP strongly inhibit enzymatic hydrolysis of pure cellulose, pure xylan, and pretreated corn stover , and that xylooligomers were more inhibitory to cellulase than xylose or xylan for an equivalent amount of xylose or than equal molar amounts of glucose or cellobiose . Figure 7 reports glucose yields against the concentration of xylooligomers in solution following enzymatic hydrolysis for 72 hours over the full range of enzyme loadings employed in this study, with the concentration of xylooligomers calculated on an equivalent xylose mass basis. First, these results show that DA solids released much less xylooligomers during enzymatic hydrolysis than solids from IL or AFEX. In addition, the xylooligomer concentrations remained virtually constant after 72 hours of enzymatic hydrolysis for all three pretreated solids. These results also show that xylooligomer concentrations had no clear effect on the trends in 72-hour glucose yields from enzymatic hydrolysis of the three pretreated solids. In fact, 72-hour glucose yields from enzymatic hydrolysis of DA and AFEX pretreated solids increased significantly with enzyme loading even though the xylooligomer concentration remained virtually the same for each. On the other hand, 72-hour glucose yields from IL pretreated solids were high and changed little despite having a xylooligomer concentration that was about two-thirds of that for enzymatic hydrolysis of AFEX pretreated solids. Therefore, other factors such as lignin removal, unproductive binding of enzyme, or cellulose structure appeared to have a greater effect on glucose yields.
Comparison to results with model compounds
Two model compounds, microcrystalline Avicel cellulose and RAC, were enzymatically hydrolyzed as well. Figure 1 shows that glucose release was greatest from enzymatic hydrolysis of RAC and lowest from Avicel cellulose at the highest and lowest enzyme loadings applied in this study over almost the entire hydrolysis time. These trends are generally reinforced for the 1-hour and 72-hour glucose yields in Figures 2 and 3, respectively. In all cases, glucose yields from enzymatic hydrolysis of IL pretreated solids closely paralleled those with RAC. RAC was a highly homogeneous substrate with disrupted hydrogen bonds  and consequently had much higher glucose yields. Other than xylan and lignin removal, cellulose crystallinity is believed to be one of the major factors limiting cellulose enzymatic hydrolysis [48, 49]. The high glucose yields from enzymatic hydrolysis of IL corn stover and RAC were probably due to reduction in crystalline cellulose content and/or altered cellulose structure previously shown for corn stover [36, 50]. The rapid hydrolysis of amorphous substrate could be explained as a homogeneous reaction that enabled cleavage of all β-glycosidic bonds randomly, resulting in a rapid reduction of DP . This result is consistent with an earlier hypothesis that lower crystallinity has a particularly significant influence on initial glucose yields from enzymatic hydrolysis .
Possible causes of differences in sugar release
Based on the hydrolysis model reported by Zhang and Lynd , three processes occur simultaneously when enzymes act on insoluble cellulosic substrates: 1) chemical and physical changes in the solid residue; 2) primary hydrolysis in which the solid phase is hydrolyzed into soluble cellodextrins; and 3) secondary hydrolysis in which the soluble oligomers are further hydrolyzed into monomers. Given that the rate of primary hydrolysis is much slower than the rate of secondary hydrolysis, a substrate with greater primary hydrolysis sugar release should result in more rapid initial glucose release. The experimental observation of similar glucose yield patterns for IL pretreated corn stover and RAC solids suggest structural similarities. However, cellulose in corn stover from DA and AFEX pretreatment are expected to be more crystalline, while Avicel cellulose is known to be highly crystalline. This difference in crystallinity could at least partially explain why glucose yields from IL corn stover solids were higher than from the AFEX and DA pretreated solids and much higher than from Avicel, particularly at shorter times.
Adsorption of CTec2 and HTec2 on pretreated corn stover
Enzyme adsorption onto the substrate is the primary step in enzymatic degradation of cellulose [9, 51]. Cellulose accessibility to enzyme has long been recognized as an essential factor controlling enzymatic hydrolysis of cellulosic biomass [52–54], and enzymatic hydrolysis rates and yields are often claimed to be related to enzyme adsorption [42, 52, 53, 55, 56]. Adsorption parameters calculated for the Langmuir model, the maximum adsorption capacity σ and equilibrium constant Kd, are summarized in Table 3. These results show substantial variances in enzyme adsorption with pretreatment type. AFEX corn stover had the lowest maximum enzyme adsorption capacity for both CTec2 and HTec2, while IL corn stover had the highest values for both. In line with this reasoning, the initial hydrolysis yields of the three pretreated substrates reported in Figures 1 and 2 followed the same trend as their maximum enzyme adsorption capacities for both CTec2 and HTec2. Thus, enzyme adsorption onto solids and their effectiveness are affected by pretreatment type and biomass composition, consistent with other published information [47, 53, 57].
No single factor absolutely dominated early and longer-term glucose yields from enzymatic hydrolysis of solids from AFEX, DA, and IL pretreatments. The high initial hydrolysis yields from IL corn stover correlated with high lignin removal, high change in crystallinity, and high enzyme adsorption, and was very similar in pattern to results from enzymatic digestion of RAC solids. The final glucose yields did not follow a consistent trend with concentration of xylooligomers released from xylan during hydrolysis. IL pretreated corn stover showed the highest initial glucose yields at low enzyme loadings, while DA pretreated corn stover, which removed the most xylan, achieved the highest glucose yields at high enzyme loadings.
Materials and methods
Pretreated corn stover and model compounds
Corn stover was harvested in September 2008 at the Michigan State University Farms (East Lansing, MI, USA) from the corn hybrid NK 49-E3 (Syngenta, Basel, Switzerland), typical of that grown in the Great Lakes region. Solids resulting from pretreatment of the same source of corn stover were prepared by the collaboration partners of the Bioenergy Research Centers (BRCs), as follows: DA pretreatment by BESC at UCR, AFEX by GLBRC at Michigan State University, and IL by JBEI. Upon receipt, the AFEX and IL pretreated corn stover solids were immediately refrigerated at 4°C until further analysis. The pretreatment conditions summarized in Table 1 for all three pretreatments were selected based on highest total glucan plus xylan yields from both pretreatment and enzymatic digestion, but only the solids were employed in the enzymatic hydrolysis study reported here.
Pure cellulose (Avicel PH101, catalogue number 11365, lot number 1094627) was purchased from FMC Corporation (Philadelphia, PA, USA). RAC was prepared from Avicel PH101 according to the method reported by Zhang and coworkers . Beechwood xylan (lot number BCBS8393V) was purchased from Sigma Chemicals (St Louis, MO, USA). Moisture content and compositional analysis of the corn stover solids and model compounds were determined according to the NREL LAP .
Cellic CTec2 (batch number VCNI0001) and Cellic HTec2 (batch number VHN0001) enzymes were generously provided by Novozymes North America, Inc., and Multifect Pectinase (batch number 4861295753) was from DuPont Industrial Biosciences. Table 4 shows the enzyme protein concentrations determined by the Kjeldahl method , with the nitrogen factor (NF) calculated by Equation 1:
in which the percentage of protein was calculated as:
In accordance with the NREL LAP , enzymatic hydrolysis was conducted in triplicate at a solids loading corresponding to 1% (w/w) glucan in 0.05 M citrate buffer (pH = 4.9) containing 10 mg/mL sodium azide in 50 mL Erlenmeyer flasks. The slurries were incubated at 50°C for 120 hours in a shaker incubator (Multitron Infors-HT, ATR Biotech, Laurel, MD, USA) at 150 rpm. Enzyme loadings were 3, 6, 12, and 30 mg of total protein/g glucan in the raw biomass. Enzyme combinations of Cellic CTec2, Cellic HTec2, and Multifect Pectinase to achieve maximum sugar release for solids from DA, AFEX, and IL pretreatments were determined by GLBRC using their novel high-throughput microplate hydrolysis method , and are shown in Table 4.
Hydrolysis samples were collected at 1, 2, 4, 8, 24, 48, 72, and 120 hours. To determine the amount of sugar generated from enzymatic hydrolysis, 400 μL samples were drawn, filtered through 0.2 μm nylon filter vials (Alltech Associates Inc., Deerfield, IL, USA), pipetted into 500 μL polyethylene HPLC vials, and then stored at 4°C until analysis. Glucan to glucose and xylan to xylose hydrolysis yields were calculated according to the following two equations, respectively:
in which GH, CB, and XH are the measured masses of glucose, cellobiose, and xylose released from enzymatic hydrolysis; GP and XP are the masses of glucan and xylan available in the pretreated biomass; and the factors 1.111, 1.136, and 1.053 account for the mass gained during hydrolysis of glucan to glucose, xylan to xylose, and cellobiose to glucose, respectively.
Basis for enzyme protein loading per gram of glucan in raw biomass
Consistent with the approach used by our team in prior research at the recommendation of the Consortium for Applied Fundamentals and Innovation (CAFI) Advisory Board, enzyme loadings for all enzymatic digestion experiments in this study were based on glucan content in the original raw material [1, 35]. Loading enzyme based on glucan content in raw biomass better represents the cost of enzyme per amount of potential ethanol, and also benefits removing more glucan in pretreatment with more enzyme per unit of glucan left in the solids to enzymatic hydrolysis. This comparison is particularly important for enzymatic hydrolysis at commercially viable low enzyme loadings. Because of the differences in glucan removal by the three pretreatments of interest here, the enzyme loadings per gram of glucan in the pretreated biomass solids varied as shown in Table 5. The result is that solids from DA and IL pretreatments had higher enzyme loadings per gram of glucan in the pretreated solids compared to solids from AFEX.
Estimation of the amounts of oligomers
To determine the total amount of glucose and xylose oligomers generated by enzymatic hydrolysis, liquid samples following enzymatic hydrolysis for 4, 24, and 72 hours were subjected to post-hydrolysis according to the NREL LAP . In particular, slurries after enzymatic hydrolysis were centrifuged to separate solids from liquid. Then, the liquid was incubated for 1 hour with 4% sulfuric acid at 121°C in an autoclave (model HA300MII; Hirayama Manufacturing Corporation, Saitama, Japan) along with sugar recovery standards. It is important to note that post-hydrolysis was carried out in 1.5 mL high recovery glass HPLC vials (Agilent, Santa Clara, CA, USA) and scaled down to 1 mL reaction volume instead of applying the conventional method in 125 mL pressure bottles with 5 to 20 mL liquid . Following post-hydrolysis, about 400 μL samples were withdrawn, pipetted into 500 μL polyethylene HPLC vials, and kept at 4°C or frozen at −20°C until further analysis. From this information, the percentage of the total glucose in solution that was glucooligomers with a DP > cellobiose, G3+, was calculated by:
X2+, the percentage yield of xylooligomers containing two or more xylose units, was calculated as:
In addition, the percentage of the total xylose in solution that was oligomers containing two or more xylose units was calculated as:
GH’ and XH’ represent the masses of glucose and xylose measured after post-hydrolysis and adjusting for losses by the sugar recovery standard .
Samples along with appropriate calibration standards were run on a Waters Alliance HPLC system (Model e-2695; Waters Corporation, Milford, MA, USA) employing an Aminex® HPX-87H column (Bio-Rad Laboratories, Life Science Research, Hercules, CA, USA). Samples were processed at an eluent (5 mM sulfuric acid) flow rate of 0.60 mL/min using a refractive index (RI) detector (Model 2414; Waters Corporation). The chromatograms were recorded and processed with Empower® 2 software (Waters Corporation).
Adsorption experiments were performed at 4°C in 0.05 M citrate buffer (pH = 4.8 ± 0.2) in 15 mL test tubes (catalogue number 430055; Thermo Fisher Scientific Inc., Waltham, MA, USA) with a biomass loading to achieve 1% w/w glucan with enzyme loadings of 0 to 2,000 mg protein/g glucan (0 to 20 mg protein/mL). The tubes containing biomass slurry and enzyme proteins were mounted on a variable speed rugged rotator (Glass-Col, LLC, Terre Haute, IN, USA) and equilibrated for 6 hours at 40 rpm. Following equilibration, the tubes were centrifuged (model Allegra X-15R; Beckman Coulter, Fullerton, CA, USA) for 15 minutes at 3,500 rpm for solid–liquid separation, the liquid was decanted, and the tubes dried overnight at 105°C. The adsorbed protein amount was directly determined by the nitrogen factor method described above . The nitrogen content of the dried and homogenized biomass solids was measured using a Flash EATM 112 N/Protein plus CHNS/O Analyzer (CE Elantech, Lakewood, NJ, USA) with atropine as a standard (catalogue number 33835210; CE Elantech). Adsorption data was non-linearly fit to a Langmuir model according to Equation 8 [7, 63]:
in which [CE] is the amount of adsorbed enzyme in mg/mL, [Ef] is the free enzyme concentration in mg/mL, σ is the maximum adsorption capacity in mg/mg substrate, [St] is the substrate concentration mg/mL, and Kd is the equilibrium constant equal to [C] [E]/[CE].
Ammonia fiber expansion
BioEnergy Science Center
Bioenergy Research Centers
Consortium for Applied Fundamentals and Innovation
Dilute sulfuric acid
Degree of polymerization
Great Lakes Bioenergy Research Center
High performance liquid chromatography
Joint BioEnergy Institute
Laboratory Analytical Procedure
National Renewable Energy Laboratory
Regenerated amorphous cellulose
University of California, Riverside.
Wyman CE, Dale BE, Elander RT, Holtzapple M, Ladisch MR, Lee YY: Coordinated development of leading biomass pretreatment technologies. Bioresour Technol 2005, 96: 1959-1966. 10.1016/j.biortech.2005.01.010
Himmel ME, Ding SY, Johnson DK, Adney WS, Nimlos MR, Brady JW, Foust TD: Biomass recalcitrance: engineering plants and enzymes for biofuels production. Science 2007, 315: 804-807. 10.1126/science.1137016
Kamm B, Kamm M: Principles of biorefineries. Appl Microbiol Biotechnol 2004, 64: 137-145. 10.1007/s00253-003-1537-7
Jorgensen H, Kristensen JB, Felby C: Enzymatic conversion of lignocellulose into fermentable sugars: challenges and opportunities. Biofuel Bioprod Bioresour 2007, 1: 119-134. 10.1002/bbb.4
Ragauskas AJ, Williams CK, Davison BH, Britovsek G, Cairney J, Eckert CA, Frederick WJ Jr, Hallett JP, Leak DJ, Liotta CL, Mielenz JR, Murphy R, Templer R, Tschaplinski T: The path forward for biofuels and biomaterials. Science 2006, 311: 484-489. 10.1126/science.1114736
Henrissat B: Celluases and their interaction with cellulose. Cellulose 1994, 1: 169-196. 10.1007/BF00813506
Lynd LR, Weimer PJ, van Zyl WH, Pretorius IS: Microbial cellulose utilization: fundamentals and biotechnology. Microbiol Mol Biol Rev 2002, 66: 506-739. 10.1128/MMBR.66.3.506-577.2002
Zhang YHP, Lynd LR: Toward an aggregated understanding of enzymatic hydrolysis of cellulose: noncomplexed cellulase systems. Biotechnol Bioeng 2004, 88: 797-824. 10.1002/bit.20282
Bansal P, Hall M, Realff MJ, Lee JH, Bommarius AS: Modeling cellulase kinetics on lignocellulosic substrates. Biotechnol Adv 2009, 27: 833-848. 10.1016/j.biotechadv.2009.06.005
Kumar R, Wyman CE: Effects of cellulase and xylanase enzymes on the deconstruction of solids from pretreatment of poplar by leading technologies. Biotechnol Prog 2009, 25: 302-314. 10.1002/btpr.102
Mosier N, Wyman C, Dale B, Elander R, Lee YY, Holtzapple M, Ladisch M: Features of promising technologies for pretreatment of lignocellulosic biomass. Bioresour Technol 2005, 96: 673-686. 10.1016/j.biortech.2004.06.025
Yang B, Wyman CE: Pretreatment: the key to unlocking low-cost cellulosic ethanol. Biofuel Bioprod Bioresour 2008, 2: 26-40. 10.1002/bbb.49
Hsu TA: Pretreatment of biomass. In Handbook on Bioethonal Production and Utilization. Edited by: Wyman CE. Washington, DC: Taylor & Francis; 1996.
Hu F, Ragauskas A: Pretreatment and lignocellulosic chemistry. Bioenergy Res 2012, 5: 1043-1066. 10.1007/s12155-012-9208-0
Knappert D, Grethlein H, Converse A: Partial acid hydrolysis of poplar wood as a pretreatment for enzymatic-hydrolysis. Biotechnol Bioeng 1981, 11: 67-77.
Yang B, Wyman CE: Effect of xylan and lignin removal by batch and flowthrough pretreatment on the enzymatic digestibility of corn stover cellulose. Biotechnol Bioeng 2004, 86: 88-95. 10.1002/bit.20043
Ohgren K, Bura R, Saddler J, Zacchi G: Effect of hemicellulose and lignin removal on enzymatic hydrolysis of steam pretreated corn stover. Bioresour Technol 2007, 98: 2503-2510. 10.1016/j.biortech.2006.09.003
Dale BE, Moreira MJ: A freeze-explosion technique for increasing cellulose hydrolysis. Biotechnol Bioeng 1982, 12: 31-43.
Holtzapple MT, Jun JH, Ashok G, Patibandla SL, Dale BE: The ammonia freeze explosion (AFEX) process. Appl Biochem Biotechnol 1991, 28–9: 59-74.
Dale BE, Henk LE, Shiang M: Fermentation of lignocellulosic materials treated by ammonia freeze-explosion. Dev Ind Microbiol 1985, 26: 223-234.
Swatloski RP, Spear SK, Holbrey JD, Rogers RD: Dissolution of cellose with ionic liquids. J Am Chem Soc 2002, 124: 4974-4975. 10.1021/ja025790m
Cheng G, Varanasi P, Li C, Liu H, Menichenko YB, Simmons BA, Kent MS, Singh S: Transition of cellulose crystalline structure and surface morphology of biomass as a function of ionic liquid pretreatment and its relation to enzymatic hydrolysis. Biomacromolecules 2011, 12: 933-941. 10.1021/bm101240z
Dadi AP, Schall CA, Varanasi S: Mitigation of cellulose recalcitrance to enzymatic hydrolysis by ionic liquid pretreatment. Appl Biochem Biotechnol 2007, 137–140: 407-421.
Zhao H, Jones CL, Baker GA, Xia S, Olubajo O, Person VN: Regenerating cellulose from ionic liquids for an accelerated enzymatic hydrolysis. J Biotechnol 2009, 139: 47-54. 10.1016/j.jbiotec.2008.08.009
Michalowicz G, Toussaint B, Vignon MR: Ultrastructural changes in poplar cell-wall during steam explosion treatment. Holzforschung 1991, 45: 175-179. 10.1515/hfsg.1922.214.171.124
Grethlein HE: Pretreatment for enhanced hydrolysis of cellulosic biomass. Biotechnol Adv 1984, 2: 43-62. 10.1016/0734-9750(84)90240-4
Clark TA, Mackie KL, Dare PH, McDonald AG: Steam explosion of the softwood Pinus radiata with sulfur dioxide addition. 2. process characterization. J Wood Chem Tech 1989, 9: 135-166. 10.1080/02773818908050291
Wong KKY, Deverell KF, Mackie KL, Clark TA, Donaldson LA: The relationship between fiber porosity and cellulose digestibility in steam-exploded Pinus radiata . Biotechnol Bioeng 1988, 31: 447-456. 10.1002/bit.260310509
Selig MJ, Viamajala S, Decker SR, Tucker MP, Himmel ME, Vinzant TB: Deposition of lignin droplets produced during dilute acid pretreatment of maize stems retards enzymatic hydrolysis of cellulose. Biotechnol Prog 2007, 23: 1333-1339. 10.1021/bp0702018
Grous WR, Converse AO, Grethlein HE: Effect of steam explosion pretreatment of pore size and enzymatic-hydrolysis of poplar. Enzyme Microb Technol 1986, 8: 274-280. 10.1016/0141-0229(86)90021-9
Kumar R, Mago G, Balan V, Wyman CE: Physical and chemical characterizations of corn stover and poplar solids resulting from leading pretreatment technologies. Bioresour Technol 2009, 100: 3948-3962. 10.1016/j.biortech.2009.01.075
Chundawat SPS, Bellesia G, Uppugundla N, Sousa LC, Gao D, Cheh AM, Agarwal UP, Bianchetti CM, Phillips GN Jr, Langan P, Balan V, Gnanakaran S, Dale BE: Restructuring the crystalline cellulose hydrogen bond network enhances its depolymerization rate. J Am Chem Soc 2011, 133: 11163-11174. 10.1021/ja2011115
Chundawat SPS, Donohoe BS, Sousa LC, Elder T, Agarwal UP, Lu F, Ralph J, Himmel ME, Balan V, Dale BE: Multi-scale visualization and characterization of lignocellulosic plant cell wall deconstruction during thermochemical pretreatment. Energy Environ Sci 2011, 4: 973-984. 10.1039/c0ee00574f
Arora R, Manisseri C, Li C, Ong M, Scheller H, Vogel K, Simmons B, Singh S: Monitoring and analyzing process streams towards understanding ionic liquid pretreatment of switchgrass ( Panicum virgatum L.). Bioenergy Res 2010, 3: 134-145. 10.1007/s12155-010-9087-1
Wyman CE, Dale BE, Elander RT, Holtzapple M, Ladisch MR, Lee YY: Comparative sugar recovery data from laboratory scale application of leading pretreatment technologies to corn stover. Bioresour Technol 2005, 96: 2026-2032. 10.1016/j.biortech.2005.01.018
Li C, Knierim B, Manisseri C, Arora R, Scheller HV, Auer M, Vogel KP, Simmons BA, Singh S: Comparison of dilute acid and ionic liquid pretreatment of switchgrass: biomass recalcitrance, delignification and enzymatic saccharification. Bioresour Technol 2010, 101: 4900-4906. 10.1016/j.biortech.2009.10.066
Shi J, Ebrik MA, Yang B, Garlock RJ, Balan V, Dale BE, Pallapolu VR, Lee YY, Kim Y, Mosier NS, Ladisch MR, Holtzapple MT, Falls M, Sierra-Ramirez R, Donohoe BS, Vinzant TB, Elander RT, Hames B, Thomas S, Warner RE, Wyman CE: Application of cellulase and hemicellulase to pure xylan, pure cellulose, and switchgrass solids from leading pretreatments. Bioresour Technol 2011, 102: 11080-11088. 10.1016/j.biortech.2011.04.003
Selig M, Weiss N, Ji Y Technical Report NREL/TP-510-42629. In Enzymatic Saccharification of Lignocellulosic Biomass. Golden, CO: National Renewable Energy Laboratory; 2008.
Chundawat SPS, Balan V, Dale BE: High-throughput microplate technique for enzymatic hydrolysis of lignocellulosic Biomass. Biotechnol Bioeng 2008, 99: 1281-1294. 10.1002/bit.21805
Hu J, Arantes V, Saddler J: The enhancement of enzymatic hydrolysis of lignocellulosic substrates by the addition of accessory enzymes such as xylanase: is it an additive or synergistic effect? Biotechnol Biofuels 2011, 4: 36. 10.1186/1754-6834-4-36
Sluiter A, Hames B, Ruiz R, Scarlata C, Sluiter J, Templeton D Technical Report NREL/TP-510-42623. In Determination of Sugars, Byproducts, and Degradation Products in Liquid Fraction Process Samples. Golden, CO: National Renewable Energy Laboratory; 2008.
Jeoh T, Ishizawa CI, Davis MF, Himmel ME, Adney WS, Johnson DK: Cellulase digestibility of pretreated biomass is limited by cellulose accessibility. Biotechnol Bioeng 2007, 98: 112-122. 10.1002/bit.21408
Kumar R, Wyman CE: Effect of enzyme supplementation at moderate cellulase loadings on initial glucose and xylose release from corn stover solids pretreated by leading technologies. Biotechnol Bioeng 2009, 102: 457-467. 10.1002/bit.22068
Qing Q, Yang B, Wyman CE: Xylooligomers are strong inhibitors of cellulose hydrolysis by enzymes. Bioresour Technol 2010, 101: 9624-9630. 10.1016/j.biortech.2010.06.137
Qing Q, Wyman CE: Supplementation with xylanase and beta-xylosidase to reduce xylo-oligomer and xylan inhibition of enzymatic hydrolysis of cellulose and pretreated corn stover. Biotechnol Biofuels 2011, 4: 18. 10.1186/1754-6834-4-18
Chang V, Holtzapple M: Fundamental factors affecting biomass enzymatic reactivity. Appl Biochem Biotechnol 2000, 84–86: 5-37.
Kumar R, Wyman CE: Cellulase adsorption and relationship to features of corn stover solids produced by leading pretreatments. Biotechnol Bioeng 2009, 103: 252-267. 10.1002/bit.22258
Zhang YHP, Cui JB, Lynd LR, Kuang LR: A transition from cellulose swelling to cellulose dissolution by o-phosphoric acid: evidence from enzymatic hydrolysis and supramolecular structure. Biomacromolecules 2006, 7: 644-648. 10.1021/bm050799c
Zhang S, Wolfgang DE, Wilson DB: Substrate heterogeneity causes the nonlinear kinetics of insoluble cellulose hydrolysis. Biotechnol Bioeng 1999, 66: 35-41. 10.1002/(SICI)1097-0290(1999)66:1<35::AID-BIT3>3.0.CO;2-G
Singh S, Simmons BA, Vogel KP: Visualization of biomass solubilization and cellulose regeneration during ionic liquid pretreatment of switchgrass. Biotechnol Bioeng 2009, 104: 68-75. 10.1002/bit.22386
Stahlberg J, Johansson G, Pettersson G: A new model for enzymatic-hydrolysis of cellulose based on the two-domain structure of cellobiohydrolyase I. Nat Biotechnol 1991, 9: 286-290. 10.1038/nbt0391-286
Rollin JA, Zhu Z, Sathitsuksanoh N, Zhang YHP: Increasing cellulose accessibility is more important than removing lignin: a comparison of cellulose solvent-based lignocellulose fractionation and soaking in aqueous ammonia. Biotechnol Bioeng 2011, 108: 22-30. 10.1002/bit.22919
Kumar R, Wyman CE: Physical and chemical features of pretreated biomass that influence macro-/micro-accessibility and biological processing. In Aqueous Pretreatment of Plant Biomass for Biological and Chemical Conversion to Fuels and Chemicals. Edited by: Wyman CE. Chichester: John Wiley & Sons Ltd; 2013:281-310.
Arantes V, Saddler J: Cellulose accessibility limits the effectiveness of minimum cellulase loading on the efficient hydrolysis of pretreated lignocellulosic substrates. Biotechnol Biofuels 2011, 4: 3. 10.1186/1754-6834-4-3
Kotiranta P, Karlsson J, Siika-aho M, Medve J, Viikari L, Tjerneld F, Tenkanen M: Adsorption and activity of Trichoderma reesei cellobiohydrolase I, endoglucanase II, and the corresponding core proteins on steam pretreated willow. Appl Biochem Biotechnol 1999, 81: 81-90. 10.1385/ABAB:81:2:81
Lou H, Zhu JY, Lan TQ, Lai H, Qiu X: pH-Induced lignin surface modification to reduce nonspecific cellulase binding and enhance enzymatic saccharification of lignocelluloses. ChemSusChem 2013, 6: 919-927. 10.1002/cssc.201200859
Kumar R, Wyman CE: Access of cellulase to cellulose and lignin for poplar solids produced by leading pretreatment technologies. Biotechnol Prog 2009, 25: 807-819. 10.1002/btpr.153
Sluiter A, Hames B, Ruiz R, Scarlata C, Sluiter J, Templeton D, Crocker D Technical Report NREL/TP-510-42618. In Determination of Structural Carbohydrates and Lignin in Biomass. Golden, CO: National Renewable Energy Laboratory; 2011.
Association of Official Analytical Chemists (AOAC): Protein (crude) determination in animal feed: copper catalyst Kjeldahl method (984.13). In Official Methods of Analysis. 15th edition. Gaithersburg, MD: AOAC International; 1990.
Kumar R, Wyman CE: An improved method to directly estimate cellulase adsorption on biomass solids. Enzyme Microb Technol 2008, 42: 426-433. 10.1016/j.enzmictec.2007.12.005
Sluiter A, Hames B, Hyman D, Payne C, Ruiz R, Scarlata C, Sluiter J, Templeton D, Wolfe J Technical Report NREL/TP-510-42621. In Determination of Total Solids in Biomass and Total Dissolved Solids in Liquid Process Samples. Golden, CO: National Renewable Energy Laboratory; 2008.
DeMartini JD, Studer MH, Wyman CE: Small-scale and automatable high-throughput compositional analysis of biomass. Biotechnol Bioeng 2011, 108: 306-312. 10.1002/bit.22937
Beldman G, Voragen AGJ, Rombouts FM, Searlevanleeuwen MF, Pilnik W: Adsorption and kinetic-behavior of purified endoglucanases and exoglucanases from Trichoderma viride . Biotechnol Bioeng 1987, 30: 251-257. 10.1002/bit.260300215
We gratefully acknowledge support for this research by the Office of Biological and Environmental Research in the Department of Energy (DOE) Office of Science through the BESC at Oak Ridge National Laboratory (contract DE-PS02-06ER64304), GLBRC (grant DE‒FC02‒07ER64494), and JBEI (grant DE-AC02-05CH11231). We are also grateful to the Center for Environmental Research and Technology of the Bourns College of Engineering (CE-CERT) at UCR for providing key equipment and facilities. We thank Mr. Charles Donald Jr for preparing AFEX pretreated corn stover for this project and Nirmal Uppugundla for having optimized the commercial enzyme formulations for the three different pretreated solids. We also thank Novozymes and DuPont Genencor Science for providing enzymes for this research. The corresponding author is particularly grateful to the Ford Motor Company for funding the Chair in Environmental Engineering at the CE-CERT at UCR that augments support for many projects such as this.
The authors declare that CEW is a cofounder of Mascoma Corporation (Lebanon, NH, USA) and former chair of their Scientific Advisory Board. CEW no longer works with Mascoma. In addition, CEW is founding Editor-in-Chief of Biotechnology for Biofuels. The other authors declare that they have no competing interests.
XG performed pretreatment of corn stover with dilute acid, all enzymatic hydrolysis experiments and characterization work reported here, prepared the initial manuscript, and undertook final assembly of the revised paper. CEW developed the initial enzymatic hydrolysis and dilute acid pretreatment experimental design, supervised the work, revised the manuscript, figures, tables, and preparation of correspondence, and approved the final manuscript. RK assisted in the design of experiments, reviewed the results, and prepared and reviewed the manuscript. BED initiated the collaboration, arrangements for supply of corn stover and AFEX pretreated solids, and reviewed the manuscript. VB supplied the corn stover, provision of AFEX pretreated materials, and reviewed the manuscript. BAS supplied the IL pretreated materials and reviewed the manuscript. SS supplied the IL pretreated materials and reviewed the manuscript. All authors read and approved the final manuscript.
Authors’ original submitted files for images
Below are the links to the authors’ original submitted files for images.
About this article
Cite this article
Gao, X., Kumar, R., Singh, S. et al. Comparison of enzymatic reactivity of corn stover solids prepared by dilute acid, AFEX™, and ionic liquid pretreatments. Biotechnol Biofuels 7, 71 (2014) doi:10.1186/1754-6834-7-71
- Corn stover
- Enzyme adsorption