Lipid production by the oleaginous yeast Yarrowia lipolytica using industrial by-products under different culture conditions

Background Microbial lipid production using renewable feedstock shows great promise for the biodiesel industry. Results In this study, the ability of a lipid-engineered Yarrowia lipolytica strain JMY4086 to produce lipids using molasses and crude glycerol under different oxygenation conditions and at different inoculum densities was evaluated in fed-batch cultures. The greatest lipid content, 31% of CDW, was obtained using a low-density inoculum, a constant agitation rate of 800 rpm, and an oxygenation rate of 1.5 L/min. When the strain was cultured for 450 h in a chemostat containing a nitrogen-limited medium (dilution rate of 0.01 h−1; 250 g/L crude glycerol), volumetric lipid productivity was 0.43 g/L/h and biomass yield was 60 g CDW/L. The coefficient of lipid yield to glycerol consumption (YL/gly) and the coefficient of lipid yield to biomass yield (YL/X) were equal to 0.1 and 0.4, respectively. Conclusions These results indicate that lipids may be produced using renewable feedstock, thus providing a means of decreasing the cost of biodiesel production. Furthermore, using molasses for biomass production and recycling glycerol from the biodiesel industry should allow biolipids to be sustainably produced.


Background
The distinct possibility of fossil fuel depletion is currently forcing the fuel industry to develop alternative energy sources, such as biodiesel [1]. Because biodiesel is derived from vegetable oils, there is competition between biodiesel producers and food crop farmers for arable lands [2]. Consequently, one of the industry's goals is to find novel ways of producing biodiesel. One possible strategy involves the transformation of waste materials and/or co-products, such as whey, crop residues, crude glycerol, or crude fats, into triglycerides or fatty acids using microbial cell factories [3,4]. These processes are advantageous compared to conventional methods, since they use waste materials generated by various industries as feedstock. Moreover, microbial lipid can be produced in close proximity to biodiesel industrial plants and it is easy to scale up their production [5].
Different bacteria, yeasts, algae, and fungi have the ability to convert carbohydrates and other substrates into intracellular lipid. When a microorganism's intracellular lipid accumulation levels are greater than 20% of cell dry weight (CDW), it is labeled an "oleaginous microorganism". Oleaginous microorganisms include yeast species, such as Rhodosporidium sp., Rhodotorula sp., Lipomyces sp., and Yarrowia lipolytica, whose intracellular lipid accumulation levels can reach 80% of CDW [6][7][8]. The main components of the accumulated lipid are triacylglycerols composed of long-chain fatty acids (16-18 carbon atoms in the chain) [6][7][8].
There are many ways of increasing intracellular lipid accumulation. Some involve metabolically engineering microbial strains to either improve their lipid storage capacities or synthesize lipids with specific fatty acid profiles [8][9][10][11]. Others focus on refining the production process by identifying optimal culture conditions and defining optimal medium composition [12][13][14]. For instance, fed-batch culturing is the most convenient system in pilot experiments seeking to establish optimal production conditions: it helps identify the best medium composition and any supplements needed. However, continuous cultures are also of great interest when the goal is to enhance lipid accumulation levels, especially those of yeast grown as well-dispersed, non-filamentous cells [15].
Due to Y. lipolytica's unique physiological characteristics (i.e., its ability to metabolize hydrophobic substrates such as alkanes, fatty acids, and lipids), its ability to accumulate high levels of lipids, and its suite of efficient genetic tools [16], this yeast is a model organism for biolipid production and it is thought to have great applied potential [6][7][8]11], both in the production of typical biofuel lipids [9][10][11] and oils with unusual fatty acid profiles or polyunsaturated fatty acids [3,4,17]. In this study, Y. lipolytica JMY4086, a strain with an improved lipid accumulation capacity, was used to exploit unpurified, lowcost industrial by-products, such as sugar beet molasses and the crude glycerol produced by the biodiesel industry and lipid production under different culture conditions was quantified. Molasses was used as a source of carbon, minerals, and vitamins, which are crucial for fermentation [18]. Moreover, molasses is used as the main substrate in the production of baker's yeast, organic acids, amino acids, and acetone/butanol [15]. In yeast, the glycolytic pathway produces intermediate compounds from glycerol either via the phosphorylation pathway [19,20] or the oxidative pathway (dehydrogenation of glycerol and the subsequent phosphorylation of the reaction product) [21]. Dihydroxyacetone phosphate, the product of these reactions, can subsequently be converted into citric acid, storage lipids, or various other products [22,23]. Additionally, glycerol may be readily incorporated in the core of triglycerides, which are stored in lipid bodies along with steryl esters [10].
The aim of this study was to produce valuable information that could be used in future research examining the biotransformation of crude glycerol into triglycerides (TAGs) with a view to producing biolipids, also known as single-cell oils (SCOs). This process may serve as an alternative means of decreasing biodiesel production costs while simultaneously recycling glycerol.

Results and discussion
Previous work has found that Y. lipolytica JMY4086 can produce biolipids from substrates such as pure glucose, fructose, and sucrose in batch bioreactors [19]. The present study investigated whether low-cost raw materials such as molasses and crude glycerol could also serve as substrates for biolipid production and accumulation; the substrate concentration, oxygenation conditions, and inoculum densities were varied. Compared to other oleaginous microorganisms, Y. lipolytica has the unique ability to accumulate lipids when nitrogen is limited and to remobilize them when carbon is limited [24]. Therefore, all culturing was performed under low nitrogen conditions. Furthermore, TAG remobilization was avoided because the TGL4 gene, which encodes triglyceride lipase YlTgl4, was deleted from JMY4086 [17].

Fed-batch cultures subject to different oxygenation conditions and initiated with different inoculum densities
Studies examining lipid production by Y. lipolytica using fed-batch or repeated-batch cultures are scarce. Moreover, only glycerol has been used as a substrate for cell growth and lipid synthesis [25]. This study utilized a two-step process: biomass was produced using molasses for 48 h, and then lipids were produced using glycerol as the main carbon source. Biomass yield and lipid production were analyzed at two different inoculum densities (low density and high density) and under two sets of oxygenation conditions (unregulated and regulated). In the unregulated strategy "Oxy-const", dissolved oxygen (DO) was not regulated; in the regulated strategy "Oxy-regul", DO was regulated at 50% saturation (see "Methods").
When Oxy-const strategy and low-density inoculum were used, the biomass reached 50 g CDW/L and citric acid production was 36.8 g/L after 55 h of culture (Figure 1a, b). During the glycerol-feeding phase, cells converted the citric acid produced into lipids. In those conditions, total lipid concentration increased from 11 to 15.5 g/L ( Figure 1c). Yeast lipid content reached 31% of CDW, which corresponds to a volumetric lipid productivity (Q L ) of 0.18 g/L/h and a coefficient of lipid yield to glycerol consumption (Y L/gly ) of 0.083 g/g (Table 1). This condition also produced a small amount of mycelial cells ( Figure 2a). Indeed, low DO levels have been shown to induce the yeast-to-mycelium transition in Y. lipolytica. Bellou and colleagues demonstrated that mycelial and/or pseudomycelial forms predominated over the yeast form when DO was low, regardless of the carbon and nitrogen sources used [26].
When oxygenation was regulated and a low-density inoculum was used, cell growth was surprisingly very slow (r x = 0.24 gCDW/h) and the culture duration (the time required for complete glycerol consumption) was 190 h. Consequently, when crude glycerol was fed into the bioreactor at 48 h, the fructose concentration was still high (30 g/L). In this condition, the biomass yield was lower (40 g/L) because citric acid production was greater (50 g/L) (Figure 1a, b); there was an apparent trade-off between the two processes. The citric acid produced was never reconsumed. The total lipid content was very low, 7 g/L, which corresponds to a Q L of 0.04 g/L/h ( Figure 1c; Table 1). However, Y L/gly and Y L/X were equal to 0.056 and 0.17 g/g, respectively (Table 1). In these conditions, JMY4086 formed short true mycelia and pseudomycelia (Figure 2b).
High-density inocula were also used under both regulated and unregulated oxygenation conditions. As shown in Figure 1, the lag phase became shorter and culture duration decreased significantly; the latter was 70 and 66 h under regulated and unregulated conditions, respectively. When oxygenation was unregulated, the biomass yield was 58 g/L; it reached 70 g/L when oxygenation was regulated ( Figure 1a). Citric acid production was similar across the two conditions (19 and 23 g/L, respectively); however, it was only reconsumed when DO was regulated ( Figure 1b). In both cases, compared to the unregulated/low-density condition, Q L was low, as were Y L/gly and Y L/X (Table 1). Furthermore, in both conditions, JMY4086 formed short true mycelia and pseudomycelia (Figure 2c, d).
Because the fed-batch culture initiated with a lowdensity inoculum and subject to unregulated oxygenation had the highest lipid production, these conditions were used in a second experiment, in which a higher airflow rate of 3.5 L/min (the high-oxygen condition, "Oxy-high") was utilized. As a consequence, the lag phase lengthened, sucrose hydrolysis began later-after 30 h ( Figure 3)-and lipid accumulation was limited. Citric acid production exceeded 40 g/L, and the compound was not reconsumed (Figure 3). The biomass yield was 59 g/L, and final lipid content was 7.7 g/L, which corresponds to a Y L/gly of 0.077 g/g (Table 1). These results indicate that increasing the oxygenation rate did not improve yeast growth and lipid production.
The fed-batch experiments revealed that the highest Q L , Y L/gly , and Y L/X values were obtained using a lowdensity inoculum and unregulated oxygenation. Consequently, these conditions were used in the continuous culture pilot experiment.

Continuous culture experiment: effects of increasing concentrations of glycerol in the feeding medium
Little research has looked at the synthesis of biolipids from sugars or renewable feedstock by nitrogen-limited continuous cultures [27][28][29]. Papanikolaou and Aggelis conducted the only study to date to examine biolipid synthesis by Y. lipolytica under continuous culture conditions using glycerol as the sole substrate [15].
In this experiment, we used a stepwise continuous fed-batch (SCFB) approach to test the effect of glycerol concentration on lipid production. The cultures started as batch cultures that were grown with molasses to produce biomass; once the sugar supply was exhausted, continuous culturing was initiated. Glycerol was used as feed, and the dilution rate was 0.01 h −1 . The glycerol concentration in the feeding medium was increased from 100 to 450 g/L in steps that took place every 100 h ( Figure 4). It has been shown that the dilution rate and Effect of oxygenation conditions and inoculation densities on growth, citric acid production, and lipid production by Y. lipolytica grown in molasses. Strain JMY4086 was grown in a molasses medium and fed with crude glycerol. Growth is expressed as a cell dry weight, b citric acid production, and c lipid production. X biomass, CA citric acid, L lipids, 1 low-density inoculum/unregulated oxygenation condition (filled circles), 2 low-density inoculum/regulated oxygenation condition (filled squares), 3 high-density inoculum/unregulated oxygenation condition (filled triangles), 4 high-density inoculum/ regulated oxygenation condition (filled diagonals). The low-density and high-density inocula had optical densities of OD 600 = 1 and OD 600 = 6, respectively. For the unregulated oxygenation condition, stirring speed was a constant 800 rpm and the aeration rate was 1.5 L/min. For the regulated oxygenation condition, dissolved oxygen was maintained at 50% saturation and the aeration rate was 0-3.5 L/ min. All the results presented are the mean values ± SD for two independent biological replicates.
culture-medium C:N ratio strongly affect lipid accumulation [28,30]. In general, dilution rates of less than 0.06 h −1 have been shown to maximize lipid production in continuous cultures across different yeasts [31]. However, a higher dilution rate, of about 0.01 h −1 , optimizes Y. lipolytica's production of citric acid from glycerol [32]. Therefore, in this experiment, a dilution rate of 0.01 h −1 was used. In addition, for JMY4086, lipid accumulation levels were similar across a range of C:N ratios, from 60:1 to 120:1 [19]. Consequently, to maximize cell growth and prevent nitrogen starvation, SCFB culturing was performed using a C:N ratio of 60:1. Biomass yield and lipid production depended on the glycerol concentration in the feed solution ( Figure 4). For Table 1 Lipid production by Y. lipolytica JMY4086 during the glycerol-feeding phase for different oxygenation conditions and inoculation densities Standard deviations were less than 10% of the mean values.
Q L volumetric lipid productivity from crude glycerol, Y L/gly coefficient of lipid yield to glycerol consumption, Y L/X coefficient of lipid yield to biomass yield.

Oxygenation (% dissolved oxygen)
Inoculum density Q L (g/L/h) Y L/gly (g/g) Y L/X (g/g)   Table 2). Under such conditions, DO was not limiting, except after 600 h of culture (data not shown). Glycerol was never detected in the culture broth, except at higher feeding concentrations (450 g/L), where glycerol accumulated in the culture broth at a concentration of 0.5 g/L. By comparison, Meesters et al. [33] observed that, in Cryptococcus curvatus, cell growth was restricted during lipid accumulation when glycerol concentrations were higher than 64 g/L. The highest Y L/gly value was obtained at a glycerol concentration of 100 g/L. However, since biomass yield was lowest at that concentration, Q L was also low (0.09 g/L/h). In contrast, when the glycerol concentration was 250 g/L, Q L and Y L/X were 0.31 g/L/h and 0.46, respectively. At higher glycerol concentrations (350 and 450 g/L), both Y L/ gly and Y L/X were lower (Table 2). During SCFB culturing, very low concentrations of citric acid were present until 400 h. Then, as the glycerol concentration increased to 350 g/L, citric acid started to accumulate; it reached a concentration of 40 g/L ( Table 2). This accumulation of citric acid may have resulted from nitrogen limitations or a transition in cell morphology. Indeed, cells occurred in yeast form up until 400 h, at which point they started to filament, forming true mycelia and pseudomycelia (data not shown).

Lipid production from glycerol in a chemostat culture
The SCFB culturing experiment showed that feed glycerol concentrations of 250 g/L yielded the highest Q L and Y L/X values. In addition, citric acid and glycerol did not accumulate under those conditions; DO levels exceeded 70% saturation and no mycelia were observed. To assess lipid production in continuous cultures, yeasts were grown in a chemostat for over 400 h using a dilution rate of 0.01 h −1 . To start off, yeasts were batch cultured for 48 h using molasses as the primary carbon source. Then, chemostat culturing was used; yeasts were kept in a medium with a glycerol concentration of 100 g/L for 100 h. They were then given a medium with a glycerol concentration of 250 g/L (Figure 5). At a steady state, between 200 h and 500 h of culture, the biomass yield was 59.8 g/L. The yeast produced 24.2 g/L of lipids; Q L was 0.43 g/L/h; and Y L/gly and Y L/X were 0.1 and 0.4 , respectively ( Table 2). Under these conditions, citric acid production was 50 g/L ( Figure 5; Table 2). In contrast to the SCFB experiments, citric acid was produced from the start in the chemostat culture. One hypothesis explaining this difference between the two culture methods is that, in the chemostat, DO was limited. During SCFB culture, DO was not a limiting factor until 600 h into the experiment, when citric acid began to be secreted into the culture broth. However, in the chemostat culture, when the glycerol concentration in the feeding medium was increased to 250 g/L, DO dramatically decreased. DO limitations resulted in citric acid secretion, but not in cell filamentation. The cell morphology was constant; indeed, during the whole culturing process, cells remained in yeast form

Table 2 Characteristics of lipid production in continuous cultures of Y. lipolytica JMY4086 grown in crude glycerol; SCFB and chemostat culturing were used
Mean values for biomass yield, volumetric lipid productivity (Q L ), the coefficient of lipid yield to glycerol consumption (Y L/gly ), and the coefficient of lipid yield to biomass yield (Y L/X ) were calculated for the full duration of the different feeding conditions (i.e., different glycerol concentrations).
nd not detected.

Culture method
Glycerol feeding (g/L)  ( Figure 6). Fatty acid profiles were similar across the three types of cultures (fed-batch, SCFB, and chemostat; Table 3). The yeast produced mainly C16 and C18 long-chain fatty acids, as do other oleaginous yeasts [25,32]. In general, differences in fatty acid profiles seem to result not from culture type, but from substrate type. When industrial fats have been used as carbon sources, yeast demonstrates a different total fatty acid composition, which is characterized by high levels of cellular stearic acid [3].

Q L (g/L/h)
The results of this study represent a good starting point for research seeking to further optimize chemostat culturing conditions. We found that the concentration of dissolved oxygen is one of the most important factors affecting lipid production. Oxygen limitation can be rate limiting in carbon metabolism and results in citric acid secretion. Additionally, optimizing nitrogen levels in the medium is also an important means by which citric acid secretion can be restricted. However, increasing nitrogen concentration can also increase biomass production, which in turn can result in problems with the oxygenation and stirring of the medium. It is therefore important to balance the regulation of available nitrogen with the optimization of the dilution rate to avoid generating overly high biomass concentrations in the bioreactor. All of these parameters should be used to find the right equilibrium between biomass and lipid production, the goal being to maximize total lipid production using chemostat culturing.

Conclusions
In conclusion, the results obtained in this study clearly show that the continuous culture method is an interesting means of producing lipids. Overall lipid production in the continuous culture experiment was almost 2.3 times higher than that in the fed-batch culture experiment. Y. lipolytica JMY4086 produced 24.2 g/L of lipids; the coefficient of lipid yield to glycerol consumption (Y L/ gly ) was 0.1 g/g and volumetric lipid productivity (Q L ) was 0.43 g/L/h. In the fed-batch cultures, lipid concentrations never exceeded 15.5 g/L, which corresponded to a Y L/gly of 0.083 g/g and a Q L of 0.18 g/L/h. Bioengineered Y. lipolytica strain JMY4086 shows promise in the development of industrial biodiesel production processes. Indeed, in this strain, the inhibition of the degradation and remobilization pathways (via the deletion of the six POX genes and the TGL4 gene, respectively) was combined with the boosting of lipid synthesis pathways (via overexpression of DGA2 and GPD1). Additionally, molasses is an excellent substrate for biomass production, because it is cheap and contains several other compounds that are crucial for the fermentation processes. However, its concentration must be controlled   because it also contains compounds that inhibit Y. lipolytica growth. Moreover, the subsequent addition of glycerol did not delay cell growth. This study provided valuable foundational knowledge that can be used in future studies to further optimize lipid production in fedbatch and continuous cultures in which biomass production takes place in molasses and lipid production takes place in industrial glycerol-based medium.

Strain
The Y. lipolytica strain used in this study, JMY4086 [17], was obtained by deleting the POX1-6 genes (POX1-POX6) that encode acyl-coenzyme A oxidases and the TGL4 gene, which encodes an intracellular triglyceride lipase. The aim was to block the β-oxidation pathway and inhibit TAG remobilization, respectively. In addition, to push and pull TAG biosynthesis, YlDGA2 and YlGPD1, which encode the major acyl-CoA:diacylglycerol acyltransferase and glycerol-3-phosphate dehydrogenase, respectively, were constitutively overexpressed. Additionally, the S. cerevisiae invertase SUC2 and Y. lipolytica hexokinase HXK1 genes were overexpressed to allow the strain to grow in molasses.

Medium and culturing conditions
The YPD medium contained Bacto ™ Peptone (20 g/L, Difco, Paris, France), yeast extract (10 g/L, Difco, Paris, France), and glucose (20 g/L, Merck, Fontenay-sous-Bois, France). The medium for the batch cultures contained molasses (245 g/L, sucrose content of 600 g/L, Lesaffre, Rangueil, France), NH 4 Cl (4.0 g/L), KH 2 PO 4 (0.5 g/L), MgCl 2 (1.0 g/L), and YNB (without amino acids and ammonium sulfate, 1.5 g/L, Difco). For fed-batch cultures, crude glycerol (96% w/v, Novance, Venette, France) was added after 48 h at a feeding rate of 8.8 g/h until a total of 100 g/L of glycerol had been delivered (C:N ratio of 100:1). In the stepwise continuous fed-batch (SCFB) cultures, a C:N ratio of 60:1 was maintained as glycerol concentrations increased (100, 200, 250, 350, and 450 g/L); NH 4 Cl ranged from 4 to 12.5 g/L. Chemostat cultures were grown in either crude glycerol (100 g/L)/ NH 4 Cl (2.5 g/L), with a C:N ratio of 25, or glycerol (250 g/L)/NH 4 Cl (6,25 g/l), with a C:N ratio of 40. Toward the beginning of the culturing process (at 100 h), the concentration of glycerol in the feeding medium was 100 g/L; it was subsequently increased to 250 g/L. This approach was used because past observations had suggested that slowly increasing the concentration of the carbon source in the feeding medium results in greater oxygenation of the culture and higher lipid production. Additionally, the fact that the carbon source was present in high concentrations from the beginning of the culturing process resulted in strong cell filamentation and lower final lipid yields (data not shown). For the stepwise continuous fed-batch and chemostat cultures, the dilution rate was 0.01 h −1 and the working volume was maintained at 1.5 L. All culturing took place in a 5-L stirred tank reactor (Biostat B-plus, Sartorius, Germany). The temperature was controlled at 28°C and the pH was kept at 3.5 by adding 40% (W/V) NaOH. We used three oxygenation conditions in our experiments: unregulated dissolved oxygen (DO), "Oxy-const", regulated DO, "Oxy-regul", and high DO, "Oxy-high" conditions. For the unregulated condition, the airflow rate was 1.5 L/min and the stirring speed was 800 rpm. In the regulated condition, DO was maintained at 50% saturation by a PID controller (the airflow rate ranged between 0 and 3.5 L/min, and stirring speed ranged between 200 and 1,000 rpm). In the oxy-high condition, the airflow rate was 3.5 L/min and the stirring speed was 800 rpm. Bioreactors were inoculated using samples with an initial OD 600 nm of 0.15 (low-density inoculum) or of 0.8 (high-density inoculum). Precultures were grown in YPD medium. The bioreactor containing a given medium (prepared with tap water) was sterilized in an autoclave at 121°C for 20 min. We conducted two biological replicates of all fed-batch cultures, for which means and standard deviations were calculated. A single replicate was performed for the SCFB and the chemostat culture.

Quantifying dry biomass
Ten milliliters of culture broth was centrifuged for 5 min at 13,000 rpm. The cell pellet was washed with distilled water and filtered on membranes with a pore size of 0.45 μm. The biomass yield was determined gravimetrically after samples were dried at 105°C. It was expressed in grams of cell dry weight per liter (gCDW/L).

Measuring sugar and citric acid concentrations
The concentrations of glycerol (GLY), sucrose (SUC), glucose (GLU), fructose (FRU), and citric acid (CA) were measured in the culture supernatants by HPLC (Dionex-Thermo Fisher Scientific, UK) using an Aminex HPX-87H column (Bio-Rad, Hercules, CA, USA) coupled with a refractive index (RI) detector (Shodex, Ogimachi, Japan). The column was eluted with 0.1 N sulfuric acid at 65°C at a flow rate of 0.6 ml min −1 .

Fluorescence microscopy
Images were obtained using a Zeiss Axio Imager M2 microscope (Zeiss, Le Pecq, France) with a 100× objective lens and Zeiss filter sets 45 and 46 for fluorescence microscopy. Axiovision 4.8 software (Zeiss, LePecq, France) was used for image acquisition. To make the lipid bodies visible, BodiPy ® Lipid Probe (2.5 mg/mL in ethanol; Invitrogen) was added to the cell suspension (OD 600 = 5) and the samples were incubated for 10 min at room temperature.

Quantifying lipid levels
The fatty acids (FAs) in 15-mg aliquots of freeze-dried cells were converted into methyl esters using the method described in Browse et al. [34,30]. FA methyl esters were analyzed by gas chromatography (GC) on a Varian 3900 equipped with a flame ionization detector and a Varian Factor Four vf-23 ms column, for which the bleed specification at 260°C was 3 pA (30 m, 0.25 mm, 0.25 μm). FAs were identified by comparing their GC patterns to those of commercial FA methyl ester standards (FAME32; Supelco) and quantified using the internal standard method, which involved the addition of 50 mg of commercial C17:0 (Sigma). Total lipid extractions were obtained from 100-mg samples (expressed in terms of CDW, as per Folch et al. [16]). Briefly, yeast cells were spun down, washed with water, freeze dried, and then resuspended in a 2:1 chloroform/methanol solution and vortexed with glass beads for 20 min. The organic phase was collected and washed with 0.4 mL of 0.9% NaCl solution before being dried at 60°C overnight and weighed to quantify lipid production.
In the above equations, Lipid acc is the lipid accumulated in the cells in the bioreactor (g); Lipid out the lipid accumulated in the cells drawn off from the bioreactor (g); Δ(lipid acc ) the difference in lipid acc for time period Δt; Gly in the glycerol fed to the bioreactor (g); Gly acc the glycerol accumulated in the bioreactor (g); Gly out the glycerol drawn off from the bioreactor (g); Δ(Gly acc ) the difference in Gly acc for the time period Δt; V the volume of the culture (L); Δt the duration between two measurements (h); X the biomass yield (gCDW/L); [Gly] the glycerol concentration in the feeding medium (g/L); [Gly med ] the glycerol concentration in the bioreactor (g/L); [Lipid] the lipid concentration (g/CDW); [X in ] the cell concentration in the bioreactor (gCDW/L); [X out ] the cell concentration in the culture broth drawn off from the bioreactor (gCDW/L); F the flow rate of the feeding medium (L/h). agreement no. 267196; Marie-Curie FP7 COFUND People Program). We would also like to thank Jessica Pearce and Lindsay Higgins for their language editing services.
(8) Y L/X = Lipid acc + Lipid out X in + X out ,